STEAM POWER PLANT:
A thermal power station is a power plant
in which the prime mover is steam driven. Water
is heated, turns into steam and spins a steam
turbine which drives an electrical generator. After it passes
through the turbine, the steam is condensed
in a condenser and recycled to where it was heated;
this is known as a Rankine cycle. The greatest variation in the design
of thermal power stations is due to the different fuel sources. Some prefer to
use the term energy center because such facilities convert forms of heat energy into
electricity. Some thermal power plants also deliver heat energy for industrial
purposes, for district heating, or for desalination
of water as well as delivering electrical power. A large proportion of CO2
is produced by the worlds fossil fired thermal power plants; efforts to reduce
these outputs are various and widespread.
The four main circuits one would come across in any
thermal power plant layout are
-Coal andAshCircuit
-AirandGasCircuit
- Feed Water and Steam Circuit
- Cooling Water Circuit
Coal and Ash Circuit
Coal and Ash circuit in a thermal power plant layout mainly takes care of feeding the boiler with coal from the storage for combustion. The ash that is generated during combustion is collected at the back of the boiler and removed to the ash storage by scrap conveyors. The combustion in the Coal and Ash circuit is controlled by regulating the speed and the quality of coal entering the grate and the damper openings.
Air and Gas Circuit
Air from the atmosphere is directed into the furnace through the air preheated by the action of a forced draught fan or induced draught fan. The dust from the air is removed before it enters the combustion chamber of the thermal power plant layout. The exhaust gases from the combustion heat the air, which goes through a heat exchanger and is finally let off into the environment.
Feed Water and Steam Circuit
The steam produced in the boiler is supplied to the turbines to generate power. The steam that is expelled by the prime mover in the thermal power plant layout is then condensed in a condenser for re-use in the boiler. The condensed water is forced through a pump into the feed water heaters where it is heated using the steam from different points in the turbine. To make up for the lost steam and water while passing through the various components of the thermal power plant layout, feed water is supplied through external sources. Feed water is purified in a purifying plant to reduce the dissolve salts that could scale the boiler tubes.
Cooling Water Circuit
The quantity of cooling water required to cool the steam in a thermal power plant layout is significantly high and hence it is supplied from a natural water source like a lake or a river. After passing through screens that remove particles that can plug the condenser tubes in a thermal power plant layout, it is passed through the condenser where the steam is condensed. The water is finally discharged back into the water source after cooling. Cooling water circuit can also be a closed system where the cooled water is sent through cooling towers for re-use in the power plant. The cooling water circulation in the condenser of a thermal power plant layout helps in maintaining a low pressure in the condenser all throughout.
All these circuits are integrated to form a thermal power plant layout that generates electricity to meet our needs.
-Coal andAshCircuit
-AirandGasCircuit
- Feed Water and Steam Circuit
- Cooling Water Circuit
Coal and Ash Circuit
Coal and Ash circuit in a thermal power plant layout mainly takes care of feeding the boiler with coal from the storage for combustion. The ash that is generated during combustion is collected at the back of the boiler and removed to the ash storage by scrap conveyors. The combustion in the Coal and Ash circuit is controlled by regulating the speed and the quality of coal entering the grate and the damper openings.
Air and Gas Circuit
Air from the atmosphere is directed into the furnace through the air preheated by the action of a forced draught fan or induced draught fan. The dust from the air is removed before it enters the combustion chamber of the thermal power plant layout. The exhaust gases from the combustion heat the air, which goes through a heat exchanger and is finally let off into the environment.
Feed Water and Steam Circuit
The steam produced in the boiler is supplied to the turbines to generate power. The steam that is expelled by the prime mover in the thermal power plant layout is then condensed in a condenser for re-use in the boiler. The condensed water is forced through a pump into the feed water heaters where it is heated using the steam from different points in the turbine. To make up for the lost steam and water while passing through the various components of the thermal power plant layout, feed water is supplied through external sources. Feed water is purified in a purifying plant to reduce the dissolve salts that could scale the boiler tubes.
Cooling Water Circuit
The quantity of cooling water required to cool the steam in a thermal power plant layout is significantly high and hence it is supplied from a natural water source like a lake or a river. After passing through screens that remove particles that can plug the condenser tubes in a thermal power plant layout, it is passed through the condenser where the steam is condensed. The water is finally discharged back into the water source after cooling. Cooling water circuit can also be a closed system where the cooled water is sent through cooling towers for re-use in the power plant. The cooling water circulation in the condenser of a thermal power plant layout helps in maintaining a low pressure in the condenser all throughout.
All these circuits are integrated to form a thermal power plant layout that generates electricity to meet our needs.
கருத்துகள் இல்லை:
கருத்துரையிடுக