திங்கள், 16 ஜூன், 2014

STEAM POWER PLANT



STEAM POWER PLANT
             Coal needs to be stored at various stages of the preparation process, and conveyed around the CPP facilities. Coal handling is part of the larger field of bulk material handling, and is a complex and vital part of the CPP.

Stockpiles

           Stockpiles provide surge capacity to various parts of the CPP. ROM coal is delivered with large variations in production rate of tonnes per hour (tph). A ROM stockpile is used to allow the washplant to be fed coal at lower, constant rate.            A simple stockpile is formed by machinery dumping coal into a pile, either from dump trucks, pushed into heaps with bulldozers or from conveyor booms. More controlled stockpiles are formed using stackers to form piles along the length of a conveyor, and reclaimers to retrieve the coal when required for product loading, etc.             Taller and wider stockpiles reduce the land area required to store a set tonnage of coal. Larger coal stockpiles have a reduced rate of heat lost, leading to a higher risk of spontaneous combustion.

Stacking

         Travelling, lugging boom stackers that straddle a feed conveyor are commonly used to create coal stockpiles.

 

Reclaiming

            Tunnel conveyors can be fed by a continuous slot hopper or bunker beneath the stockpile to reclaim material. Front-end loaders and bulldozers can be used to push the coal into feeders. Sometimes front-end loaders are the only means of reclaiming coal from the stockpile. This has a low up-front capital cost, but much higher operating costs, measured in dollars per tonne handled. High-capacity stockpiles are commonly reclaimed using bucket-wheel reclaimers. These can achieve very high rates
ASH HANDLING SYSTEMS:
Ash Handling Systems is the none / un combusted portion or residue, after taking combustion of any solid fuel.

Solid fuel is usually coal. And any coal contains some non combustible portion which is called ash. Content of that coal.
There are different types of ashes.
• Bottom ash
• fly ash.

Bottom ash is the residue which remains in the solid form at the bottom and fly ash is the light particle which goes out along with exhaust gases, and usually they are collected in chimneys.

Taking their so formed ash away from the Plant / Boiler is called – "ASH HANDLING SYSTEM" This is done in either
• Mechanical conveying
• Pneumatic conveying
Mechanical system requires conveyors, and Pneumatic system requires – compressed air to carry out the ash.
COMBUSTION EQUIPMENTS:
Combustion control options range from electro / mechanical through to full microprocessor control systems to match both application and customer needs.

Cochran supply an extensive range of fuel handling equipment to complement and help ensure that the optimum performance from the combustion and control equipment is maintained. Fuel handling equipment includes gas boosters, oil pumping and heating stations, fuel metering and instrumentation packages are available to match individual installation requirements.
STOCKERS:
A mechanical stoker is a device which feeds coal into the firebox of a boiler. It is standard equipment on large stationary boilers and was also fitted to large steam locomotives to ease the burden of the fireman. The locomotive type has a screw conveyor (driven by an auxiliary steam engine) which feeds the coal into the firebox. The coal is then distributed across the grate by steam jets, controlled by the fireman. Power stations usually use pulverized coal-fired boilers.
PULVERISER:
A pulverizer or grinder is a mechanical device for the grinding of many different types of materials. For example, they are used to pulverize coal for combustion in the steam-generating furnaces of fossil fuel power plants.

Types of pulverizers

Ball and tube mills

A ball mill is a pulverizer that consists of a horizontal rotating cylinder, up to three diameters in length, containing a charge of tumbling or cascading steel balls, pebbles, or rods.
A tube mill is a revolving cylinder of up to five diameters in length used for fine pulverization of ore, rock, and other such materials; the material, mixed with water, is fed into the chamber from one end, and passes out the other end as slime (slurry).

Ring and ball mill

This type of mill consists of two rings separated by a series of large balls. The lower ring rotates, while the upper ring presses down on the balls via a set of spring and adjuster assemblies. The material to be pulverized is introduced into the center or side of the pulverizer (depending on the design) and is ground as the lower ring rotates causing the balls to orbit between the upper and lower rings. The pulverized material is carried out of the mill by the flow of air moving through it. The size of the pulverized particles released from the grinding section of the mill is determined by a classifer separator.

Vertical roller mill

Similar to the ring and ball mill, this mill uses large "tires" to crush the coal. These are usually found in utility plants.
Raw coal is gravity-fed through a central feed pipe to the grinding table where it flows outwardly by centrifugal action and is ground between the rollers and table. Hot primary air for drying and coal transport enters the windbox plenum underneath the grinding table and flows upward through a swirl ring having multiple sloped nozzles surrounding the grinding table. The air mixes with and dries coal in the grinding zone and carries pulverized coal particles upward into a classifier.
Fine pulverized coal exits the outlet section through multiple discharge coal pipes leading to the burners, while oversized coal particles are rejected and returned to the grinding zone for further grinding. Pyrites and extraneous dense impurity material fall through the nozzle ring and are plowed, by scraper blades attached to the grinding table, into the pyrites chamber to be removed. Mechanically, the vertical roller mill is categorized as an applied force mill. There are three grinding roller wheel assemblies in the mill grinding section, which are mounted on a loading frame via pivot point. The fixed-axis roller in each roller wheel assembly rotates on a segmentally-lined grinding table that is supported and driven by a planetary gear reducer direct-coupled to a motor. The grinding force for coal pulverization is applied by a loading frame. This frame is connected by vertical tension rods to three hydraulic cylinders secured to the mill foundation. All forces used in the pulverizing process are transmitted to the foundation via the gear reducer and loading elements. The pendulum movement of the roller wheels provides a freedom for wheels to move in a radial direction, which results in no radial loading against the mill housing during the pulverizing process.
Depending on the required coal fineness, there are two types of classifier that may be selected for a vertical roller mill. The dynamic classifier, which consists of a stationary angled inlet vane assembly surrounding a rotating vane assembly or cage, is capable of producing micron fine pulverized coal with a narrow particle size distribution. In addition, adjusting the speed of the rotating cage can easily change the intensity of the centrifugal force field in the classification zone to achieve coal fineness control real-time to make immediate accommodation for a change in fuel or boiler load conditions. For the applications where a micron fine pulverized coal is not necessary, the static classifier, which consists of a cone equipped with adjustable vanes, is an option at a lower cost since it contains no moving parts. With adequate mill grinding capacity, a vertical mill equipped with a static classifier is capable of producing a coal fineness up to 99.5% or higher <50 mesh and 80% or higher <200 mesh, while one equipped with a dynamic classifier produces coal fineness levels of 100% <100 mesh and 95% <200 mesh, or better.

Bowl mill

Similar to the vertical roller mill, it also uses tires to crush coal. There are two types, a deep bowl mill, and a shallow bowl mill.

Demolition pulverizer

An attachment fitted to an excavator. Commonly used in demolition work to break up large pieces of concrete.
ELECTROSTATIC PRECIPITATOR:
An electrostatic precipitator (ESP), or electrostatic air cleaner is a particulate collection device that removes particles from a flowing gas (such as air) using the force of an induced electrostatic charge. Electrostatic precipitators are highly efficient filtration devices that minimally impede the flow of gases through the device, and can easily remove fine particulate matter such as dust and smoke from the air stream.[1] In contrast to wet scrubbers which apply energy directly to the flowing fluid medium, an ESP applies energy only to the particulate matter being collected and therefore is very efficient in its consumption of energy (in the form of electricity).

Modern industrial electrostatic precipitators

ESPs continue to be excellent devices for control of many industrial particulate emissions, including smoke from electricity-generating utilities (coal and oil fired), salt cake collection from black liquor boilers in pulp mills, and catalyst collection from fluidized bed catalytic cracker units in oil refineries to name a few. These devices treat gas volumes from several hundred thousand ACFM to 2.5 million ACFM (1,180 m³/s) in the largest coal-fired boiler applications. For a coal-fired boiler the collection is usually performed downstream of the air preheater at about 160 °C (320 deg.F) which provides optimal resistivity of the coal-ash particles. For some difficult applications with low-sulfur fuel hot-end units have been built operating above 371 °C (700 deg.F).
The original parallel plate–weighted wire design (described above) has evolved as more efficient (and robust) discharge electrode designs were developed, today focusing on rigid (pipe-frame) discharge electrodes to which many sharpened spikes are attached (barbed wire), maximizing corona production. Transformer-rectifier systems apply voltages of 50 – 100 kV at relatively high current densities. Modern controls, such as an automatic voltage control, minimize electric sparking and prevent arcing (sparks are quenched within 1/2 cycle of the TR set), avoiding damage to the components. Automatic plate-rapping systems and hopper-evacuation systems remove the collected particulate matter while on line, theoretically allowing ESPs to stay in operation for years at a time.

Wet electrostatic precipitator

A wet electrostatic precipitator (WESP or wet ESP) operates with saturated air streams (100% relative humidity). WESPs are commonly used to remove liquid droplets such as sulfuric acid mist from industrial process gas streams. The WESP is also commonly used where the gases are high in moisture content, contain combustible particulate, have particles that are sticky in nature.
The preferred and most modern type of WESP is a downflow tubular design. This design allows the collected moisture and particulate to form a slurry that helps to keep the collection surfaces clean.
Plate style and upflow design WESPs are very unreliable and should not be used in applications where particulate is sticky in nature.

Consumer-oriented electrostatic air cleaners

Plate precipitators are commonly marketed to the public as air purifier devices or as a permanent replacement for furnace filters, but all have the undesirable attribute of being somewhat messy to clean. A negative side-effect of electrostatic precipitation devices is the production of toxic ozone and NOx. However, electrostatic precipitators offer benefits over other air purifications technologies, such as HEPA filtration, which require expensive filters and can become "production sinks" for many harmful forms of bacteria.
The two-stage design (charging section ahead of collecting section) has the benefit of minimizing ozone production which would adversely affect health of personnel working in enclosed spaces. For shipboard engine rooms where gearboxes generate an oil fog, two-stage ESP's are used to clean the air improving the operating environment and preventing buildup of flammable oil fog accumulations. Collected oil is returned to the gear lubricating system.
With electrostatic precipitators, if the collection plates are allowed to accumulate large amounts of particulate matter, the particles can sometimes bond so tightly to the metal plates that vigorous washing and scrubbing may be required to completely clean the collection plates. The close spacing of the plates can make thorough cleaning difficult, and the stack of plates often cannot be easily disassembled for cleaning. One solution, suggested by several manufacturers, is to wash the collector plates in a dishwasher.
Some consumer precipitation filters are sold with special soak-off cleaners, where the entire plate array is removed from the precipitator and soaked in a large container overnight, to help loosen the tightly bonded particulates.
A study by the Canada Mortgage and Housing Corporation testing a variety of forced-air furnace filters found that ESP filters provided the best, and most cost-effective means of cleaning air using a forced-air system.
DRAUGHT:
Most boilers now depend on mechanical draught equipment rather than natural draught. This is because natural draught is subject to outside air conditions and temperature of flue gases leaving the furnace, as well as the chimney height. All these factors make proper draught hard to attain and therefore make mechanical draught equipment much more economical.
There are three types of mechanical draught:
Induced draught: This is obtained one of three ways, the first being the "stack effect" of a heated chimney, in which the flue gas is less dense than the ambient air surrounding the boiler. The denser column of ambient air forces combustion air into and through the boiler. The second method is through use of a steam jet. The steam jet oriented in the direction of flue gas flow induces flue gasses into the stack and allows for a greater flue gas velocity increasing the overall draught in the furnace. This method was common on steam driven locomotives which could not have tall chimneys. The third method is by simply using an induced draught fan (ID fan) which removes flue gases from the furnace and forces the exhaust gas up the stack. Almost all induced draught furnaces operate with a slightly negative pressure.
Forced draught: Draught is obtained by forcing air into the furnace by means of a fan (FD fan) and ductwork. Air is often passed through an air heater; which, as the name suggests, heats the air going into the furnace in order to increase the overall efficiency of the boiler. Dampers are used to control the quantity of air admitted to the furnace. Forced draught furnaces usually have a positive pressure.
Balanced draught: Balanced draught is obtained through use of both induced and forced draught. This is more common with larger boilers where the flue gases have to travel a long distance through many boiler passes. The induced draught fan works in conjunction with the forced draught fan allowing the furnace pressure to be maintained slightly below atmospheric.
SURFACE CONDERSER:
Surface condenser is the commonly used term for a water-cooled shell and tube heat exchanger installed on the exhaust steam from a steam turbine in thermal power stations These condensers are heat exchangers which convert steam from its gaseous to its liquid state at a pressure below atmospheric pressure. Where cooling water is in short supply, an air-cooled condenser is often used. An air-cooled condenser is however significantly more expensive and cannot achieve as low a steam turbine exhaust pressure as a water cooled surface condenser.
Surface condensers are also used in applications and industries other than the condensing of steam turbine exhaust in power plants.
In thermal power plants, the primary purpose of a surface condenser is to condense the exhaust steam from a steam turbine to obtain maximum efficiency and also to convert the turbine exhaust steam into pure water (referred to as steam condensate) so that it may be reused in the steam generator or boiler as boiler feed water.
The steam turbine itself is a device to convert the heat in steam to mechanical power. The difference between the heat of steam per unit weight at the inlet to the turbine and the heat of steam per unit weight at the outlet to the turbine represents the heat which is converted to mechanical power. Therefore, the more the conversion of heat per pound or kilogram of steam to mechanical power in the turbine, the better is its efficiency. By condensing the exhaust steam of a turbine at a pressure below atmospheric pressure, the steam pressure drop between the inlet and exhaust of the turbine is increased, which increases the amount of heat available for conversion to mechanical power. Most of the heat liberated due to condensation of the exhaust steam is carried away by the cooling medium (water or air) used by the surface condenser
COOLING TOWERS:
Cooling towers are heat removal devices used to transfer process waste heat to the atmosphere. Cooling towers may either use the evaporation of water to remove process heat and cool the working fluid to near the wet-bulb air temperature or in the case of "Close Circuit Dry Cooling Towers" rely solely on air to cool the working fluid to near the dry-bulb air temperature. Common applications include cooling the circulating water used in oil refineries, chemical plants, power stations and building cooling. The towers vary in size from small roof-top units to very large hyperboloid structures that can be up to 200 metres tall and 100 metres in diameter, or rectangular structures that can be over 40 metres tall and 80 metres long. Smaller towers are normally factory-built, while larger ones are constructed on site. They are often associated with nuclear power plants in popular culture, although cooling towers are constructed on many types of buildings.

Industrial cooling towers

Industrial cooling towers can be used to remove heat from various sources such as machinery or heated process material. The primary use of large, industrial cooling towers is to remove the heat absorbed in the circulating cooling water systems used in power plants, petroleum refineries, petrochemical plants, natural gas processing plants, food processing plants, semi-conductor plants, and for other industrial facilities such as in condensers of distillation columns, for cooling liquid in crystallization, etc.[2] The circulation rate of cooling water in a typical 700 MW coal-fired power plant with a cooling tower amounts to about 71,600 cubic metres an hour (315,000 U.S. gallons per minute)[3] and the circulating water requires a supply water make-up rate of perhaps 5 percent (i.e., 3,600 cubic metres an hour).
If that same plant had no cooling tower and used once-through cooling water, it would require about 100,000 cubic metres an hour [4] and that amount of water would have to be continuously returned to the ocean, lake or river from which it was obtained and continuously re-supplied to the plant. Furthermore, discharging large amounts of hot water may raise the temperature of the receiving river or lake to an unacceptable level for the local ecosystem. Elevated water temperatures can kill fish and other aquatic organisms. (See thermal pollution.) A cooling tower serves to dissipate the heat into the atmosphere instead and wind and air diffusion spreads the heat over a much larger area than hot water can distribute heat in a body of water. Some coal-fired and nuclear power plants located in coastal areas do make use of once-through ocean water. But even there, the offshore discharge water outlet requires very careful design to avoid environmental problems.
Petroleum refineries also have very large cooling tower systems. A typical large refinery processing 40,000 metric tonnes of crude oil per day (300,000 barrels (48,000 m3) per day) circulates about 80,000 cubic metres of water per hour through its cooling tower system.
The world's tallest cooling tower is the 200 metre tall cooling tower of Niederaussem Power Station.

Heat transfer methods

With respect to the heat transfer mechanism employed, the main types are:
·         Wet cooling towers or simply open circuit cooling towers operate on the principle of evaporation. The working fluid and the evaporated fluid (usually H2O) are one and the same.
·         Dry Cooling Towers operate by heat transfer through a surface that separates the working fluid from ambient air, such as in a tube to air heat exchanger, utilizing convective heat transfer. They do not use evaporation.
·         Fluid coolers or Closed Circuit Cooling Towers are hybrids that pass the working fluid through a tube bundle, upon which clean water is sprayed and a fan-induced draft applied. The resulting heat transfer performance is much closer to that of a wet cooling tower, with the advantage provided by a dry cooler of protecting the working fluid from environmental exposure and contamination.
In a wet cooling tower (or Open Circuit Cooling Tower), the warm water can be cooled to a temperature lower than the ambient air dry-bulb temperature, if the air is relatively dry. (see: dew point and psychrometrics). As ambient air is drawn past a flow of water, an small portion of the water evaporate, the energy required by that portion of the water to evaporate is taken from the remaining mass of water reducing his temperature (aproximately by 970 BTU for each pound of evaporated water). Evaporation results in saturated air conditions, lowering the temperature of the water process by the tower to a value close to wet bulb air temperature, which is lower than the ambient dry bulb air temperature, the difference determined by the humidity of the ambient air.
To achieve better performance (more cooling), a medium called fill is used to increase the surface area and the time of contact between the air and water flows. Splash fill consists of material placed to interrupt the water flow causing splashing. Film fill is composed of thin sheets of material (usually PVC) upon which the water flows. Both methods create increased surface area and time of contact between the fluid (water) and the gas (air).

Air flow generation methods

With respect to drawing air through the tower, there are three types of cooling towers:
Natural draft, which utilizes buoyancy via a tall chimney. Warm, moist air naturally rises due to the density differential to the dry, cooler outside air. Warm moist air is less dense than drier air at the same pressure. This moist air buoyancy produces a current of air through the tower.
Mechanical draft, which uses power driven fan motors to force or draw air through the tower.
Induced draft: A mechanical draft tower with a fan at the discharge which pulls air through tower. The fan induces hot moist air out the discharge. This produces low entering and high exiting air velocities, reducing the possibility of recirculation in which discharged air flows back into the air intake. This fan/fin arrangement is also known as draw-through. (see Image 2, 3)
Forced draft: A mechanical draft tower with a blower type fan at the intake. The fan forces air into the tower, creating high entering and low exiting air velocities. The low exiting velocity is much more susceptible to recirculation. With the fan on the air intake, the fan is more susceptible to complications due to freezing conditions. Another disadvantage is that a forced draft design typically requires more motor horsepower than an equivalent induced draft design. The forced draft benefit is its ability to work with high static pressure. They can be installed in more confined spaces and even in some indoor situations. This fan/fill geometry is also known as blow-through. (see Image 4)
Fan assisted natural draft. A hybrid type that appears like a natural draft though airflow is assisted by a fan.
Hyperboloid (a.k.a. hyperbolic) cooling towers (Image 1) have become the design standard for all natural-draft cooling towers because of their structural strength and minimum usage of material. The hyperboloid shape also aids in accelerating the upward convective air flow, improving cooling efficiency. They are popularly associated with nuclear power plants. However, this association is misleading, as the same kind of cooling towers are often used at large coal-fired power plants as well. Similarly, not all nuclear power plants have cooling towers, instead cooling their heat exchangers with lake, river or ocean water.

 

 

 

Categorization by air-to-water flow

Crossflow

Crossflow is a design in which the air flow is directed perpendicular to the water flow (see diagram below). Air flow enters one or more vertical faces of the cooling tower to meet the fill material. Water flows (perpendicular to the air) through the fill by gravity. The air continues through the fill and thus past the water flow into an open plenum area. A distribution or hot water basin consisting of a deep pan with holes or nozzles in the bottom is utilized in a crossflow tower. Gravity distributes the water through the nozzles uniformly across the fill material.

Counterflow

In a counterflow design the air flow is directly opposite to the water flow (see diagram below). Air flow first enters an open area beneath the fill media and is then drawn up vertically. The water is sprayed through pressurized nozzles and flows downward through the fill, opposite to the air flow.
Common to both designs:
The interaction of the air and water flow allow a partial equalization and evaporation of water.
The air, now saturated with water vapor, is discharged from the cooling tower.
A collection or cold water basin is used to contain the water after its interaction with the air flow.
Both crossflow and counterflow designs can be used in natural draft and mechanical draft cooling towers.

இடுகையிட்டது நேரம்

கருத்துகள் இல்லை:

கருத்துரையிடுக

இதற்கு குழுசேர்: கருத்துரைகளை இடு (Atom)